DirectPCR Lysis Reagent (Tail)

16th Oct 2026

Protocol

1. Sample preparation

For a 0.5 cm tail, add 200–300 µl DirectPCR Lysis Reagent (Tail) containing freshly prepared 0.2–0.4 mg/ml Proteinase K (not included). Proteinase K is stable in DirectPCR reagents for approximately 24 hours.

If only a small number of tails are processed and weighing Proteinase K powder is difficult, use genomic PCR-quality Proteinase K solution at 0.5–1.0 mg/ml (25–50 µl Proteinase K solution per 1 ml DirectPCR reagent). See Table 1 for suggested starting conditions.

Note: Although 200 µl DirectPCR is usually sufficient for complete lysis of a 0.5 cm tail, using 250–300 µl provides more reproducible results because of improved mixing efficiency. Compare different volumes of DirectPCR reagents to determine the best performance. If tails are not mixed well with the solutions, use 0.75 ml tubes.

2. Tissue lysis

Rotate the tubes in a rotating hybridization oven at 55°C for 5–6 hours or until no tissue clumps are observed. If necessary, rotation can continue overnight without loss of efficacy. Complete lysis is important.

Because some tails may not remain in contact with the solutions, reposition them by shaking the bottle containing the tubes, preferably after 2–3 hours.

Note: A rotating hybridization oven generally performs better than a rocking plate. Use 0.75 ml tubes for volumes below 200 µl of DirectPCR Reagent. DNA fragmentation caused by prolonged rotation will not significantly affect PCR performance. Use approximately proportional volumes of DirectPCR Lysis Reagent for different sample sizes.

3. Proteinase K inactivation

Incubate crude lysates at 85°C for 45 minutes by floating the entire rack containing the tubes in a water bath.

Optionally, precipitate hairs by centrifuging for 10 seconds before proceeding to Step 4.

Crude lysates may be stored at −20°C for up to one year or at 4°C for up to one week without losing efficacy.

4. PCR amplification

Use 0.5–1.0 µl of lysate for a 50 µl PCR reaction. Hotmaster Taq Polymerase, JumpStart Taq DNA Polymerase, or HotStar Taq DNA Polymerase is recommended for PCR.

Rescue of DNA

DNA in crude lysates can be recovered for further analysis. Add NaCl to a final concentration of 250 mM, followed by 0.7 volume of isopropanol. DNA will form precipitates.

Centrifuge at 4°C for 2 minutes, discard the supernatant, wash the DNA with 1 ml of 70% ethanol, and dissolve it in 50 µl of 10 mM Tris-HCl (pH 8.0). Use 1 µl for PCR.

Table 1. Suggested Starting Lysis Conditions for Mouse Tails

Tail length (cm) DirectPCR (µl) Dilution (fold) Lysate (µl) per 50 µl PCR reaction
0.2–0.3 150–200 2 1.0–2.0
0.4 150–250 1 0.5–1.0
0.5 200–300 1 0.5–1.0

Related Products

Product Description
DirectPCR-Tail 500 mouse tails (100 ml)
DirectPCR-Ear 500 mouse ears (50 ml)
DirectPCR-Yolk sac Yolk sac (100 ml)
DirectPCR-Cell Cultured cells (100 ml)
Proteinase K Solution All types of tissues (100 mg)

This product is distributed for laboratory use only. Caution: Not for diagnostic use. The safety and efficacy of this product for diagnostic or other uses have not been established.

Gentaur USA, UK and Europe

Email: info@gentaur.com

Website: https://maxanim.com/contact/

Important Technical Tips

1. Complete lysis

Large tissue clumps should not remain after digestion. Vigorously shake the bottle containing the microcentrifuge tubes for 2–3 seconds, once or twice, after the tissues begin to partially dissolve. This helps disperse partially digested tissues and reposition tubes in which tails have become separated from the lysis reagents, improving overall lysis efficiency.

2. Proteinase K inactivation

Inactivating Proteinase K by incubating samples at 85–86°C for 45–50 minutes is critical to protect Taq polymerase from Proteinase K activity.

3. Taq polymerase

Various commercially available Taq polymerases have been tested. The enzymes listed above are recommended for optimal results.

4. Tissue size

Tail samples should be approximately 0.5 cm or slightly smaller. Use a minimal volume of crude lysate (0.5–1 µl per 50 µl PCR reaction). Excess DirectPCR reagent may inhibit PCR efficiency.

5. Small tubes and evaporation

To minimize evaporation, use a 0.75 ml tube when the reagent volume is below 100 µl.

6. Small samples and dilution

If the required DirectPCR reagent volume is below 50 µl, dilute the reagent up to twofold with water while maintaining the same Proteinase K concentration. If the DirectPCR reagent is diluted twofold, use twice as much crude lysate in the PCR reaction.

7. PCR machine

PCR machines can occasionally be a source of technical problems. Check the instrument settings and verify that the equipment is functioning correctly when troubleshooting unexpected results.